Contamination, ecological, and health risk assessment of heavy metals and organophosphorus pesticides in single, double, and ratoon cropping of rice: a case study in Mazandaran, North of Iran.

This study investigated the contamination and health risk assessment of heavy metals and organophosphorus pesticides in single, double, and ratoon cropping of rice in Mazandaran province, north of Iran. A total of 17 sampling locations in rice farms were selected and soil and rice samples were collected from farms in 5 counties of Mazandaran. Soil and rice samples were then transferred to the lab for further analysis. The concentration of pesticides and heavy metals was then analyzed using gas chromatography-mass spectrometry (GC-MS) and inductively coupled plasma mass spectrometry (ICP-MS), respectively. Mercury was analyzed using a Leco mercury analyzer. Target hazard quotient (THQ), total target hazard quotient (TTHQ), carcinogenic risk (CR), and total carcinogenic risk (TCR) in children and adults were used. Potential ecological risk also was used to test the possible hazards of heavy metals to the environment. Heavy metals concentration in rice and soil samples in different farming steps revealed different levels. THQ showed no considerable risk in consuming contaminated rice to adults and children considered, while TTHQ revealed potential non-carcinogenic risks. Ni had the most carcinogenic risks to target human groups, and TCR showed carcinogenicity for carcinogenic heavy metals in all stations. Findings showed no ecological risks of metals to the environment. In conclusion, rice farmers in Mazandaran use the lands multiple times during the year to increase the performance, function, quality, and quantity of rice, but the possible toxic effects of heavy metals and pesticides on consumers and the environment should not be overlooked.

Electro dialysis reversal (EDR) performance for reject brine treatment of reverse osmosis desalination system.

In this study, the performance of bench-scale EDR was evaluated using the samples taken from the 1st and the 2nd stage RO from the Brackish Water Reverse Osmosis (BWRO) plant in Eshtehard, Iran. The measurements indicated that original TDS of the aquifer brackish water was equal to 3,229-3,664 mg/L, whereas TDS of the 1st stage RO brine was between 5,500 and 7,700 mg/L, that TDS of the 2nd stage RO brine was in the range of 9,500-10,600 mg/L. A batch bench-scale EDR system of 12 l/h was used with a direct electric current at three different scenarios. In the first, the brine was fed at 20°C (as a reference regulated point). In the second, temperature (14, 20, 26.5°C), and in the third, voltage were changed (6, 12, 18, 24 V) to investigate their influences on performance of the EDR process, while the other operational parameters (feed flow rate, recovery ratio, quality of feed brine)were kept constant. Based on the data analysis using the ANOVA and DUNCAN tests for the second and third scenarios, it was observed that the optimum TDS removal efficiency of the EDR process can be at temperature of 26.5°C and voltage of 18 V. On the other hand, the successful performance of the bench-scale EDR in reducing the 29,000 mg/L TDS and the 45,000 µmhos/cm EC of the 2nd stage brine to 1,716 mg/L (TDS) and 2,640 µmhos/cm (EC) (at 26.5°C and 24V) could be considered as the main achievement of this research. Overall, the hybrid process RO-EDR-RO can be considered as the best technical, environmental and economical scenario for the development of Eshtehard Desalination Plant phase 2 at full scale.

Inhibition performances of graphene oxide/silver nanostructure for the microbial corrosion: molecular dynamic simulation study.

Steel is one of the mainly used materials in the oil and gas industry. However, it is susceptible to the marine corrosion, which 20% of the total marine corrosion is caused by microbiologically influenced corrosion (MIC). The economic and environmental impacts of corrosion are significant, and it is crucial to fight against corrosion in a proper sustainability context and environmental-friendly methods. In this study, the graphene oxide/silver nanostructure (GO-Ag) inhibitory effect on the corrosion of steel in the presence of sulfate reducing bacteria (SRB) was investigated, via weight loss (WL) and Tafel polarization measurements. Moreover, molecular dynamic (MD) simulations were performed to obtain a deep understanding of the corrosion inhibition effect of GO-Ag. GO-Ag showed a significant antibacterial effect at 80 ppm. Moreover, WL and Tafel polarization measurements illustrated a great inhibition efficiency, which reached up to 84% reduction of WL and 98% reduction of corrosion current density (Icorr) after 7 days of incubation with GO-Ag. Based on MD simulations, bonding energy reached to the larger value in the presence of GO-Ag, which indicated the ability of graphene oxide nanosheets to be adsorbed on the steel surface and prevent the access of corrosive agents to the steel surface. The radial distribution function (RDF) results implied distance between corrosive agent (water and SRB) and steel surface (Fe atoms), which indicated protection of the steel surface due to the effective adsorption of GO nanosheets through the active sites of the steel surface. The mean square displacement (MSD) result showed smaller displacement of the corrosive particles on the surface of steel, resulting that the GO-Ag molecules bonded with Fe molecules on the surface of steel.

Possible health risk assessment for heavy metal concentrations in water, sediment, and fish species and Turkmen pregnant women's biomonitoring in Miankaleh Peninsula, Iran.

This study investigated the human biomonitoring of heavy metals in the water, sediments, and tissues of mostly consumed fish species using Turkmen pregnant women's biomarkers in winter 2019, at the Miankaleh Peninsula, north of Iran. Metal concentrations were measured in various fish organs as well as pregnant women's blood, hair, and nail as biological indicators. For this purpose, a total of 20 water and sediment, 14 fish, and 16 human samples were collected. Inductively coupled plasma mass spectrometry (ICP-MS) was used to evaluate the concentration of Cr, Co, Cu, As, Hg, and Pb. Results showed metals with the highest concentrations as Cu and Cr in water (93.35 and 80.91 µg/l, respectively), Hg and Pb in sediment (7.40 µg/g for both), Cu and Pb in the liver (27.00 and 18.9 µg/g for C. carpio; 1414 and 31.7 µg/g for L. auratus), muscle (10.00 and 18.80 for C. carpio; 37.20 and 8.27 µg/g for L. auratus), and skin (26.40 and 9.90 for C. carpio; 10.80 and 11.74 µg/g for L. auratus). In addition, Cu, in pregnant women samples, had the highest values at 2.53 mg/l, 8.87, 36.46, and 29.04 µg/g for blood, hair, fingernail, and toenail, respectively. However, Co showed the lowest concentration in all studied samples. Fish liver and fingernail of pregnant women did reveal the highest heavy metal accumulation, whereas fish muscle and blood of pregnant women had the lowest accumulated heavy metals. The concentration of Hg in water, sediment, fish muscle, and women's blood and hair exceeded the limits suggested by various organizations. Therefore, this study highlighted that heavy metal concentration, in particular Hg, in water, sediments, and fish is a serious risk to the health of local inhabitants who rely on fisheries products and recommended that necessary information should be provided to warn Turkmen pregnant women in consumption of Hg-contaminated fish in this area.

Conversion of biomass to N, S co-doped porous graphene as an adsorbent for mercury vapor removal: optimization and DFT study.

This study is devoted to optimization synthesis conditions of the N, S co-doped porous graphene via a single step thermal chemical activation process from agricultural wastes such as cabbage waste. To this end, the response surface method (RSM) was considered, and the synthesis parameters were varied in specific ranges. By doing so, the optimum conditions in terms of the best performance in mercury removal was determined which was characterized by TEM, SEM, BET, XRD, XPS, and FTIR techniques. The chosen key process parameters were Activation agent to carbon precursor ratio (A: KOH/C), Reaction time (B: Time), Activation temperature (C: Temperature), and (Dopant to carbon precursor ratio (D: Dopant/C). Each parameter was investigated in 3 levels with lower and upper bounds being A: 2-6; B:30-90 min.; C: 600-800 ˚C; D:2-10. The optimum conditions of the process were determined to be as: A: 2; B: 30 min.; C: 600 ˚C and D: 2. The optimized sample was prepared in repeated runs with reproducible results with Hg vapor adsorption capacity of 2100 µg/g at 40 ˚C and 2266 µg/g at 90 ˚C. In addition to the experiments, DFT calculations were also carried out which elucidated the positive role of N and S co-doping in improving the mercury adsorption intensity. SUPPLEMENTARY INFORMATION: The online version contains supplementary material available at 10.1007/s40201-021-00712-y.

Single-step synthesis of N, S co-doped waste-derived nanoporous carbon sorbent for mercury vapor removal.

As well known, mercury is a toxic trace element due to its bioaccumulation and volatility which results in severe effects in health of ecosystems and humans' life. Herein, for the first time, the synthesis of a N and S dual-doped waste-derived graphene-like nanoporous carbon via a facile and single-step route is presented and its capability in mercury vapor removal from gas streams is investigated. To prepare a modified adsorbent, thiourea was utilized as the doping agent to induce nitrogen and sulfur dopants into the nanoporous carbon structure derived from pyrolysis of cabbage (Capitat. var. Brassica oleracea) waste from Brassicaceae family as an inherently S, N-containing precursor, which is produced in noticeable amounts annually. The prepared adsorbents were characterized through FTIR, XRD, BET, SEM, TEM, and CHNOS techniques to get an insight into the structure, morphology, and chemical characteristics of the adsorbents. The structural characterization revealed the successful synthesis of a graphene-like nanoporous carbon sheet which was doped with nitrogen and sulfur atoms. The S, N dual-doped graphene-like carbon nanosheets showed an enhanced activity toward mercury vapor adsorption. For this end, two different dopant to carbon source ratios were considered and it was found that the higher dopant amount results in a better performance. From the adsorption experiments, it was revealed that the pristine graphene-like carbon had a less performance in mercury removal (71%) compared with doped samples (more than 90%) which shows the necessity of reinforcement and surface modification of as mentioned cabbage base graphene. However, the best sample which was prepared with the dopant to carbon ratio of 10 had a performance of 94.5% removal (2100 µg/g) compared with 89% (1980 µg/g) for mercury removal by the sulfur-impregnated commercial activated carbon.

Green mitigation of microbial corrosion by copper nanoparticles doped carbon quantum dots nanohybrid.

Recently, nanomaterials have been introduced as a new generation of inhibitors to control the microbiologically influenced corrosion (MIC). In this study, copper nanoparticles doped carbon quantum dots (Cu/CQDs) nanohybrid was used as an inhibitor to reduce the MIC. FESEM, EDS, FTIR, and XRD were used to characterize the nanohybrid. The dose-response test was performed to evaluate the inhibitory effect of Cu/CQDs against SRB. Design-Expert software was used to design the matrix of experiment and analyze the result. Cu/CQDs showed significant inhibitory effect against SRB compared to the copper nanoparticles (CuNPs) and carbon quantum dots (CQDs), at 50 ppm. Moreover, corrosion behavior of X60 steel was evaluated via electrochemical impedance spectroscopy (EIS) and Tafel polarization techniques in the presence of SRB and Cu/CQDs. The fitted result of EIS showed that the charge transfer resistance (Rct) value increased in the presence of Cu/CQDs owing to the enhancement in the thickness of the electrical double layer, indicating that Cu/CQDs is able to provide significant corrosion protection to X60 steel in the presence of SRB. In addition, FESEM, EDS, and XRD were used to study the formed corrosion products and biofilm on the surface of X60 steel. Corrosion test results indicated that the addition of the Cu/CQDs reduced the surface damage of X60 steel in the presence of SRB. It is attributed to the carbon dots adsorption film formation, which possessed a significant protective ability to inhibit the corrosion of steel in the presence of SRB.

Poly (amidoamine) generation 6 functionalized Fe3O4@SiO2/GPTMS core-shell magnetic NPs as a new adsorbent for Arsenite adsorption: kinetic, isotherm and thermodynamic studies.

In this survey a new route has been developed the preparation of poly (amidoamine) generation 6 (PAMAM-G6) dendrimer functionalized Fe3O4/SiO2 nanoparticle and was used for arsenite (As (III)) adsorption. SiO2 was first grafted onto the surface of Fe3O4 to formation a core-shell structure. Then the introduction of epoxy rings were done by hydrolysis of methylsilane groups of 3-Glycidoxypropyltrimethoxysilane (GPTMS) on OH groups of SiO2 and afterwards, PAMAM-G6 reacted with epoxy rings of GPTMS to obtain a multiamino magnetic adsorbent. The as-prepared nanocomposite was characterized by TEM, Zeta potential, FESEM, VSM, FTIR, Raman and XPS techniques. The effects of reaction time from 5 to 50 min, initial As (III) concentration in the range of 1-10 mgL-1, initial adsorbent concentration in the range of 10-50 mgL-1 and initial pH in the range 3-8 were studied. The resulting of kinetic and isotherm models displays high adsorption affinity (233 mg/g) for As (III) and the adsorbent can reach the adsorbent can reach the adsorption equilibrium at a neutral pH (7). The As (III) loaded nanocomposite could be separated readily from aqueous solution by magnetic and regenerated simply via NaOH. The study of the adsorption procedure showed that the pseudo-second order kinetics and Langmuir isotherm well-fitted with the experimental data of As (III) adsorption onto nanocomposite.

Quantitative evaluation of n-alkanes, PAHs, and petroleum biomarker accumulation in beach-stranded tar balls and coastal surface sediments in the Bushehr Province, Persian Gulf (Iran).

Coastal areas within the Bushehr Province (BP), Persian Gulf, Iran, face great challenges due to the heavy organic contamination caused by rapid industrialization, and the presence of numerous oil fields. In addition, in 2014, a significant number of tar balls are found along the coasts of BP. A total of 96 samples (48 coastal sediments and 48 tar balls) were taken from eight sampling points at the BP coast during the summer of 2014. These samples were analyzed to identify the sources and characteristics of their organic matter using diagnostic ratios and fingerprint analysis based on the distribution of the source-specific biomarkers of n-alkanes, PAHs,1 hopanes and steranes. Mean concentration of n-alkanes (µg g-1 dw) and PAHs (ng g-1 dw) varied respectively from 405 to 220,626, and 267 to 23,568 in coastal sediments, while ranged respectively from 664 to 145,285 and 390 to 46,426 in tar balls. In addition, mean concentration of hopanes and steranes (ng g-1 dw) were between 18.17 and 3349 and 184.66 to 1578 in coastal sediments, whereas in tar balls were 235-1899 and 520-1504, respectively. Pri/Phy2 ratio was 0.25 to 1.51 (0.65) and 0.36 to 1 (0.63) in coastal sediment and tar ball samples, respectively, and the occurrence of UCM3 in both matrices, reflecting the petrogenic OM4 inputs and chronic oil contamination, respectively. The C30 and C29 homologues followed Gammacerane were detected in both matrices, in particular those collected from intensive industrial activities, suggesting petrogenic sources of OM. The coastal sediment PAHs profiles were significantly dominated by HMW5-PAHs in the Bahregan Beach (BAB) (78% of total PAHs), Bandare-Genaveh (GP) (66%), and Bandare-Bushehr (BUB) (61%) stations, while the Bashi Beach (BSB) (40%), Bandare-Kangan (KP) (57%), and Bandare-Asaluyeh (AP) (51%) stations exhibited higher proportion of LMW6-PAHs. PCA7 indicated that the tar ball and coastal sediment samples deposited along the Southwest of the BP beaches are most likely originated from the Abuzar oil. Based on the intensity of the anthropogenic activities, NPMDS8 analysis revealed that the GP, BAB, NNP, AP, and KP sampling sites had a high concentration of detected organic pollutants. To the best of our knowledge, this is the first study that investigates oil pollution in costal sediments and tar balls in the BP, providing insights in to the fate of oil in the coastal areas of the Persian Gulf, Iran.

In situ assessment of Karaj River genotoxic impact with the alkaline comet assay and micronucleus test, on feral brown trout (Salmo trutta fario).

The in situ evaluation of the genotoxic impact of the Karaj River was performed using the comet and micronucleus (MN) assays in erythrocytes, liver, gill and kidney of indigenous brown trout, Salmo trutta fario from three different stations, including Varangerud, Asara and Purkan. The results showed that DNA damage significantly increased in sampled fish erythrocytes, liver and gill from low levels in the upstream river (Varangerud) via intermediate levels in downstream (Purkan) to high levels in the middle of the river (Asara), correlating with the river increasing pollution gradient. Gill was the most sensitive tissue followed by blood and liver. Kidney did not respond to the genotoxic gradient of the river. MN test (as a complementary assay) of liver cells of fish was a sensitive biomarker of genotoxic exposure. MN test in blood, gill and kidney did not reflect the genotoxic condition of the river.

Spatial traffic noise pollution assessment - A case study.

OBJECTIVES: Spatial assessment of traffic noise pollution intensity will provide urban planners with approximate estimation of citizens exposure to impermissible sound levels. They could identify critical noise pollution areas wherein noise barriers should be embedded. The present study aims at using the Geographic Information System (GIS) to assess spatial changes in traffic noise pollution in Tehran, the capital of Iran, and the largest city in the Middle East. MATERIAL AND METHODS: For this purpose, while measuring equivalent sound levels at different time periods of a day and different days of a week in District 14 of Tehran, wherein there are highways and busy streets, the geographic coordination of the measurement points was recorded at the stations. The obtained results indicated that the equivalent sound level did not show a statistically significant difference between weekdays, and morning, afternoon and evening hours as well as time intervals of 10 min, 15 min and 30 min. Then, 91 stations were selected in the target area and equivalent sound level was measured for each station on 3 occasions of the morning (7:00-9:00 a.m.), afternoon (12.00-3:00 p.m.) and evening (5:00-8:00 p.m.) on Saturdays to Wednesdays. RESULTS: As the results suggest, the maximum equivalent sound level (Leq) was reported from Basij Highway, which is a very important connecting thoroughfare in the district, and was equal to 84.2 dB(A), while the minimum equivalent sound level (Leq), measured in the Fajr Hospital, was equal to 59.9 dB(A). CONCLUSIONS: The average equivalent sound level was higher than the national standard limit at all stations. The use of sound walls in Highways Basij and Mahallati as well as widening the Streets 17th Shahrivar, Pirouzi and Khavaran, benchmarked on a map, were recommended as the most effective mitigation measures. Additionally, the research findings confirm the outstanding applicability of the Geographic Information System in handling noise pollution data towards depicting noise pollution intensity caused by traffic.

Occurrence of metolachlor and trifluralin losses in the Save river agricultural catchment during floods.

Rising pesticide levels in streams draining intensively managed agricultural land have a detrimental effect on aquatic ecosystems and render water unfit for human consumption. The Soil and Water Assessment Tool (SWAT) was applied to simulate daily pesticide transfer at the outlet from an agriculturally intensive catchment of 1110 km(2) (Save river, south-western France). SWAT reliably simulated both dissolved and sorbed metolachlor and trifluralin loads and concentrations at the catchment outlet from 1998 to 2009. On average, 17 kg of metolachlor and 1 kg of trifluralin were exported at outlet each year, with annual rainfall variations considered. Surface runoff was identified as the preferred pathway for pesticide transfer, related to the good correlation between suspended sediment exportation and pesticide, in both soluble and sorbed phases. Pesticide exportation rates at catchment outlet were less than 0.1% of the applied amount. At outlet, SWAT hindcasted that (i) 61% of metolachlor and 52% of trifluralin were exported during high flows and (ii) metolachlor and trifluralin concentrations exceeded European drinking water standards of 0.1 µg L(-1) for individual pesticides during 149 (3.6%) and 17 (0.4%) days of the 1998-2009 period respectively. SWAT was shown to be a promising tool for assessing large catchment river network pesticide contamination in the event of floods but further useful developments of pesticide transfers and partition coefficient processes would need to be investigated.